絲絨毛巾檢測

絲絨毛巾檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 17780.6-2012紡織機械.安全要求.第6部分：織造機械

GB/T 17780的本部分規定了織造機械的主要危險及相關安全要求和/或措施。本部分適用于織造、針織和簇絨使用的所有機器、設備和相關裝置。本部分與GB/T 17780.1結合使用。

EN 14697-2005紡織品.絲絨毛巾和絲絨毛巾織物.規范和試驗方法

This document specifies minimum requirements for properties and test methods forThe evaluation of new readymade terry towels and to new terry fabrics, for contract and domestic use.This document covers woven terry structures only.This document does not cover towels used inThe health care sector (see ENV 14237) or cabinet roller towels (see EN 13569).

NF G33-005-2005紡織品.絲絨毛巾和絲絨織物.規范和試驗方法

Le présent document spécifie les exigences minimales pour les propriétés et les méthodes d'essai relatives à l'évaluation des serviettes éponges neuves et des tissus éponges neufs, destinés à des usages domestiques et professionnels.Le présent document couvre uniquement les structures tissées en éponge.Le présent document ne couvre pas les serviettes utilisées dans le domaine de la santé (voir l'ENV 14237) ou les serviettes essuie-mains textiles en bobine (voir l'EN 13569).

DIN EN 14697-2005紡織品.絲絨毛巾和絲絨毛巾織物.規范和試驗方法

This document specifies minimum requirements for properties and test methods for the evaluation of new ready-made terry towels and to new terry fabrics, for contract and domestic use. This document covers woven terry structures only. This document does not cover towels used in the health care sector (see ENV 14237) or cabinet roller towels (see EN 13569).#,,#

DIN EN ISO 10414-2-2011石油和天然氣工業.鉆井液的現場測試.第2部分:油基液(ISO 10414-2-2011);英文版本EN ISO 10414-2-2011,僅限CD-ROM

This part of ISO 10414 provides standard procedures for determining the following characteristics of oil-based drilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) oil, water and solids concentrations;e) alkalinity, chloride concentration and calcium concentration;f) electrical stability;g) lime and calcium concentrations, calcium chloride and sodium chloride concentrations;h) low-gravity solids and weighting material concentrations.The annexes provide additional test methods or examples that can optionally be used for the determination of:- shear strength (Annex A);- oil and water concentrations from cuttings (Annex B);- drilling fluid activity (Annex C);- aniline point (Annex D);- lime, salinity and solids concentration (Annex E);- sampling, inspection and rejection (Annex F);- rig-site sampling (Annex G);- cuttings activity (Annex H);- active sulphides (Annex I);- calibration and verification of glassware, thermometers, viscometers, retort kit cups and drilling fluid balances (Annex J);- permeability plugging apparatus with set-screw secured end cap (Annex K);- permeability plugging apparatus with threaded end cap (Annex L);- elastomer compatibility (Annex M);- sand content of oil-based fluid (Annex N);- identification and monitoring of weight-material sag (Annex O);- oil-based drilling fluid test report form (Annex P).

BS EN 14697-2005紡織品.絲絨毛巾和絲絨毛巾織物.規范和試驗方法

This document specifies minimum requirements for properties and test methods for the evaluation of new ready-made terry towels and to new terry fabrics, for contract and domestic use.\nThis document covers woven terry structures only.\nThis document does not cover towels used in the health care sector (see ENV 14237) or cabinet roller towels (see EN 13569).

BS EN ISO 10414-2-2011石油和天然氣工業.鉆井液的現場測試.油基液

This part of ISO 10414 provides standard procedures for determining the following characteristics of oil-baseddrilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) oil, water and solids concentrations;e) alkalinity, chloride concentration and calcium concentration;f) electrical stability;g) lime and calcium concentrations, calcium chloride and sodium chloride concentrations;h) low-gravity solids and weighting material concentrations.The annexes provide additional test methods or examples that can optionally be used for the determination of:- shear strength (Annex A);- oil and water concentrations from cuttings (Annex B);- drilling fluid activity (Annex C);- aniline point (Annex D);- lime, salinity and solids concentration (Annex E);- sampling, inspection and rejection (Annex F);- rig-site sampling (Annex G);- cuttings activity (Annex H);- active sulphides (Annex I);- calibration and verification of glassware, thermometers, viscometers, retort kit cups and drilling fluidbalances (Annex J);- permeability plugging apparatus with set-screw secured end cap (Annex K);- permeability plugging apparatus with threaded end cap (Annex L);- elastomer compatibility (Annex M);- sand content of oil-based fluid (Annex N);- identification and monitoring of weight-material sag (Annex O);- oil-based drilling fluid test report form (Annex P).