外墻磚檢測

外墻磚檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 4100-2015陶瓷磚

本標準規定了陶瓷磚的術語和定義、分類、性能、抽樣和接收條件、要求和試驗方法、標記和說明。本標準適用于由干壓或擠壓成型的陶瓷磚。本標準不適用于陶瓷配件磚。

GB/T 9195-2011建筑衛生陶瓷分類及術語

本標準規定了建筑衛生陶瓷的分類、術語和定義。本標準適用于建筑衛生陶瓷的設計、生產、質量檢驗、貿易、科學研究、教學等領域。

GB/T 37214-2018陶瓷外墻磚通用技術要求

本標準規定了陶瓷外墻磚的術語和定義、分類、技術要求、試驗方法、檢驗規則、標志和說明、包裝、貯存和運輸。本標準適用于吸水率不大于6%的建筑物室外墻面保護及裝飾用陶瓷外墻磚。

GB/T 41156-2021外墻磚用彈性膠粘劑

本文件規定了彈性膠粘劑的分類和命名、通用要求、試驗條件和材料、試驗方法、產品命名、標簽和注意事項。本文件適用于外墻磚鋪貼用的反應型樹脂膠粘劑。

GB/T 50310-2018(條文說明)地下鐵道工程施工標準 條文說明

隨著經濟的發展，地下鐵道工程由原來的地下隧道，發展為地上和地下的城市軌道交通，其制式也多樣化，本標準除不適用于“磁懸浮”“跨坐式”“直線電機”制式城市軌道交通外，也適用于其他制式的城市輕型軌道交通的施工。

CECS 376-2014改性無機粉復合建筑飾面片材應用技術規程

本規程適用于新建建筑和既有建筑中，采用改性無機粉復合建筑飾面片材的工程設計、施工及驗收。

CECS 443-2016泡沫玻璃板薄抹灰外墻外保溫工程技術規程

本規程適用于抗震設防烈度小于或等于8度地區，以混凝土或砌體為基層墻體的新建、擴建和改建民用建筑泡沫玻璃板薄抹灰外墻外保溫工程的設計、施工及驗收。

CECS 454-2016模塊化蒸壓加氣混凝土輕鋼復合保溫墻體工程技術規程

本規程適用于100m及以下的抗震設防烈度為6、7、8度的工業及民用建筑和既有建筑改造，自承重外圍護體系的模塊化蒸壓加氣混凝土輕鋼復合保溫墻體的設計、加工制作與運輸儲存、安裝施工、工程驗收以及維護。

JC/T 982-2005磚瓦焙燒窯爐

本標準規定了磚瓦焙燒窯爐的術語和定義、分類、技術要求、檢驗方法、檢驗規則、質量評定、標志和標簽以及包裝、運輸和貯存。 本標準適用于用于普通磚、多孔磚、空心磚、裝飾磚和空心砌塊等產品的燒結、燒成溫度在1200℃以下的熱工設備。其它類似工況的工業窯爐亦可參考使用。

JC/T 2195-2013薄型陶瓷磚

本標準規定了薄型陶瓷磚的術語和定義、分類、技術要求、試驗方法、抽樣和接收條件、標志和說明以及包裝、運輸和貯存等。本標準適用于吸水率不大于3%、表面積小于1.62 m<上標2>的薄型陶瓷磚。

JGJ/T 181-2009房屋建筑與市政基礎設施工程檢測分類標準

本標準適用于房屋建筑和市政基礎設施工程檢測的分類。

JGJ/T 277-2012紅外熱像法檢測建筑外墻飾面粘結質量技術規程

本規程適用于建筑外墻采用滿粘法施工的飾面層粘結質量檢測，不適用于下列飾面層的粘結質量檢測：1采用混色飾面磚或涂料，且影響檢測結果判斷的飾面層；2表面有較大凹凸裝飾的飾面層。

RB/T 110-2014能源管理體系.建筑衛生陶瓷企業認證要求

本標準規定了建筑衛生陶瓷企業能源管理體系的認證要求。本標準適用于建筑衛生陶瓷企業的能源管理體系認證，可用于企業建立、實施、保持和改進其能源管理體系，也可作為各相關方評價企業能源管理體系的依據。其他陶瓷企業可參照使用本標準。

DL/T 5226-2013發電廠電力網絡計算機監控系統設計技術規程

本標準適用于出線電壓等級110(66)kV及以上的新建和改(擴)建發電廠電力網絡計算機監控系統的設計。

ISO 14448-2016外墻磚面用低模量膠粘劑

This International Standard specifies a quality standard and test methods for a low modulus adhesive composed of chemical reaction resins and used for the installation of tiles to exterior walls.

ASTM C1060-2011a(2015)框架建筑包絡腔中絕緣設施熱成像檢查的標準實施規程

5.1x00a0;Although infrared imaging systems have the potential to determine many factors concerning the thermal performance of a wall, roof, floor, or ceiling, the emphasis in this practice is on determining whether insulation is missing or whether an insulation installation is malfunctioning. Anomalous thermal images from other apparent causes are not required to be recorded; however, if recorded as supplemental information, their interpretation is capable of requiring procedures and techniques not presented in this practice. 1.1x00a0;This practice is a guide to the proper use of infrared imaging systems for conducting qualitative thermal inspections of building walls, ceilings, roofs, and floors, framed in wood or metal, that contain insulation in the spaces between framing members. This procedure allows the detection of cavities where insulation is inadequate or missing and allows identification of areas with apparently adequate insulation. 1.2x00a0;This practice offers reliable means for detecting suspected missing insulation. It also offers the possibility of detecting partial-thickness insulation, improperly installed insulation, or insulation damaged in service. Proof of missing insulation or a malfunctioning envelope requires independent validation. Validation techniques, such as visual inspection or in-situ R-value measurement, are beyond the scope of this practice. 1.3x00a0;This practice is limited to frame construction even though thermography is used on all building types. (ISO 6781) 1.4x00a0;Instrumentation and calibration required under a variety of environmental conditions are described. Instrumentation requirements and measurement procedures are considered for inspections from both inside and outside the structure. Each vantage point offers visual access to areas hidden from the other side. 1.5x00a0;The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Note 1 and Note 3.

ASTM C1715-2010砌筑墻排水系統的漏水性評估的標準試驗方法

This test method is suitable for use on walls to determine the ability of masonry wall drainage systems to collect water penetrating the exterior wythe and to direct this water back to the exterior surface of the exterior wythe. Removal of a portion of the interior wall finishes is desirable to observe leakage into backup walls. Even with removal of interior finishes, in many cases it is not practical to observe surfaces behind spandrel beams, columns, or other obstructions. Potential areas where leakage may occur but that are not visible during the test shall be considered when interpreting the results of the test and shall be recorded in the report. This test method is suitable for use on mock-up walls to determine the performance of masonry wall drainage systems. This test method is suitable for evaluating the effectiveness of flashing repairs.1.1 This test method describes a standard procedure for determining the ability of masonry wall drainage systems to collect water that penetrates the exterior masonry wythe during rainstorms and to direct this water back to the exterior surface of the wall. 1.2 This test method is applicable to wall systems that contain an exterior masonry wythe with a drainage zone on the interior face of the exterior wythe. It is not applicable to single-wythe drainage walls. 1.3 This test method is not applicable to masonry barrier walls or other masonry walls that are designed without drainage zones behind the exterior wythe. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C1715/C1715M-2015評估砌筑墻排水系統漏水性能的標準試驗方法

5.1x00a0;This test method is suitable for use on walls to determine the ability of masonry wall drainage systems to collect water penetrating the exterior wythe and to direct this water back to the exterior surface of the exterior wythe. Removal of a portion of the interior wall finishes is desirable to observe leakage into backup walls. Even with removal of interior finishes, in many cases it is not practical to observe surfaces behind spandrel beams, columns, or other obstructions. Potential areas where leakage may occur but that are not visible during the test shall be considered when interpreting the results of the test and shall be recorded in the report. 5.2x00a0;This test method is suitable for use on mock-up walls to determine the performance of masonry wall drainage systems. 5.3x00a0;This test method is suitable for evaluating the effectiveness of flashing repairs. 1.1x00a0;This test method describes a standard procedure for determining the ability of masonry wall drainage systems to collect water that penetrates the exterior masonry wythe during rainstorms and to direct this water back to the exterior surface of the wall. 1.2x00a0;This test method is applicable to wall systems that contain an exterior masonry wythe with a drainage zone on the interior face of the exterior wythe. It is not applicable to single-wythe drainage walls. 1.3x00a0;This test method is not applicable to masonry barrier walls or other masonry walls that are designed without drainage zones behind the exterior wythe. 1.4x00a0;This test method covers the application of the testing using either inch-pound or SI units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5x00a0;This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.