您的位置：首頁 > 其他

焊接和螺紋用碳素鋼管檢測

發布日期： 2024-06-21 17:34:53 - 更新時間：2024年06月29日 15:22

焊接和螺紋用碳素鋼管檢測項目報價？??解決方案？??檢測周期？??樣品要求？

GB/T 32294-2015鍛制承插焊和螺紋活接頭

本標準規定了鍛制承插焊和螺紋活接頭的品種與代號、產品結構、級別、接管尺寸、訂貨內容、尺寸與公差、材料、制造、熱處理、檢驗和試驗以及標志等要求。本標準適用于工業管道系統中公稱尺寸不大于DN80(NPS 3)、級別為Class 3000的承插焊和螺紋活接頭。

GB 50235-2010工業金屬管道工程施工規范

本規范適用于設計壓力不大于42MPa，設計溫度不超過材料允許使用溫度的工業金屬管道工程的施工。本規范不適用于下列工業金屬管道的施工：1 石油、天然氣、地?zé)岬瓤碧胶筒删蜓b置的管道；2 長輸管道；3 核能裝置的專用管道；4 海上設施和礦井的管道；5 采暖通風與空氣調節的管道及非圓形截面的管道。

GB/T 51012-2014鈾濃縮工廠工藝氣體管道工程施工及驗收規范

本規范適用于設計壓力1Pa~0. 8MPa(G)、設計溫度-80℃~100℃的鈾濃縮工藝氣體管道。

GB 51035-2014電子工業純水系統安裝與驗收規范

本規范適用于新建、改建、擴建的電子工業純水系統的安裝及驗收。

GB 51110-2015潔凈廠房施工及質量驗收規范

本規范適用于新建、改建和擴建的工業潔凈廠房的施工及質量驗收。本規范中的施工質量驗收應與現行標準《建筑工程施工質量驗收統一標準》GB 50300配套使用。

GB/T 51288-2018礦山斜井凍結法施工及質量驗收標準

本標準適用于采用凍結孔豎直布置方式且沖積層厚度不超過200m的礦山斜井凍結工程施工及質量驗收。

CB/T 3790-1997船舶管子加工技術條件

本標準規定了船舶管子零件的材料、切割、裝配、焊接、彎曲、強度試驗、清洗等方面的工藝及其質量驗收指標要求。本標準適用于各類船舶的無縫鋼管、焊接鋼管、鍍鋅焊接鋼管、不銹鋼管、雙金屬管以及有色金屬管的加工。

JT/T 286-1995內河船舶軸系修理技術要求

本標準規定了船舶軸系修理前的勘驗;軸系主要零部件的修換;軸系的裝配與校中以及修復后的驗收與應提交的文件。本標準適用于內河鋼質船舶軸系的修理。海洋船舶及其它類型船舶亦可參照?qǐng)?zhí)行。

SY/T 0608-2014大型焊接低壓儲罐的設計與建造

本標準適用于具有單一垂直回轉軸，用于儲存石油中間產品(氣體或蒸氣)、成品以及其他類似液體的大型鋼制焊接低壓地上儲罐的設計與建造。本標準適用于設計壓力(表壓)小于0.1MPa (15lb/in<上標2>)，金屬溫度不高于120℃ (250℉)的儲罐。本標準的基本規定適用于低日平均環境溫度為-45℃ (-50℉)以上的建罐地區。附錄S中的低壓不銹鋼儲罐不受環境溫度的限制。附錄R適用于溫度范圍在-51℃～4. 5℃ (-60℉～+ 40℉)的冷藏產品的低壓儲罐。附錄Q適用于溫度不低于-198℃(-325℉)的液化烴氣的低壓儲罐。本標準的規定可適用于：a)盛裝或儲存液面以上存在氣相空間的液體儲罐。b)單獨盛裝或儲存氣體或蒸氣的儲罐，但不適用于懸掛式的氣體儲罐。與按本標準建造儲罐的罐體相連接的內部和外部接管，超出以下范圍的不在本標準規定范圍內：a)螺栓連接法蘭的第一個法蘭密封面。b)罐體外側螺紋連接的第一個螺紋接頭。c)焊接連接的第一道環向接頭。

DL/T 5204-2016發電廠油氣管道設計規程

本規程適用于燃煤電廠、燃?xì)?蒸汽聯合循環電廠、燃油電廠和核電廠常規部分油氣系統、管道的設計和設備選擇。油氣管道是發電廠油管道和氣體管道的總稱，包括燃油管道、潤滑油管道、天然氣管道、壓縮空氣管道、氫氣管道、氧氣管道、氮?dú)夤艿?、二氧化碳管道和抽真空管道等。本?guī)程不適用于輸送液化天然氣、液化石油氣、煤氣等的管道設計。

DB11/T 301-2005燃?xì)馐覂?nèi)工程設計施工驗收技術規定

本規定適用于北京市居民生活、商業及工業企業生產、采暖通風和空調使用的天然氣、氣態液化\r石油氣、人工煤氣作燃料的新建、擴建、改建燃?xì)馐覂?nèi)工程的設計、施工及驗收

ASTM A53/A53M-2007無縫焊接、含鋅涂層、黑色熱浸鍍鋼管標準規范

1.1 This specification covers seamless and welded black and hot-dipped galvanized steel pipe in NPS 1/8 to NPS 26 [DN 6 to DN 650] (Note 1), inclusive, with nominal wall thickness (Note 2) as given in Table X2.2 and X2.3. It shall be permissible to furnish pipe having other dimensions provided that such pipe complies with all other requirements of this specification. Supplementary requirements of an optional nature are provided and shall apply only when specified by the purchaser.Note 1 - The dimensionless designators NPS (nominal pipe size) [DN (diameter nominal)] have been substituted in this specification for such traditional terms as \"nominal diameter,\" \"size,\" and \"nominal size.\"Note 2 - The term nominal wall thickness has been assigned for the purpose of convenient designation, existing in name only, and is used to distinguish it from the actual wall thickness, which may vary over or under the nominal wall thickness.1.2 This specification covers the following types and grades: 1.2.1 Type F - Furnace-butt-welded, continuous welded Grade A, 1.2.2 Type E - Electric-resistance-welded, Grades A and B, and 1.2.3 Type S - Seamless, Grades A and B. Note 3 - See Appendix X1 for definitions of types of pipe. 1.3 Pipe ordered under this specification is intended for mechanical and pressure applications and is also acceptable for ordinary uses in steam, water, gas, and air lines. It is suitable for welding, and suitable for forming operations involving coiling, bending, and flanging, subject to the following qualifications: 1.3.1 Type F is not intended for flanging. 1.3.2 If Type S or Type E is required for close coiling or cold bending, Grade A is the preferred grade; however, this is not intended to prohibit the cold bending of Grade B pipe.1.3.3 Type E is furnished either nonexpanded or cold expanded at the option of the manufacturer. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system is to be used independently of the other.The following precautionary caveat pertains only to the test method portion, Sections 7, 8, 9, 13, 14, and 15 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.1.5 The text of this specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.

ASTM A589/A589M-2006水井用無縫和焊接碳素鋼管的標準規范

1.1 This specification covers four specific types of plain end or threaded and coupled carbon steel pipe for use in water wells. 1.2 Each type of water well pipe shall conform to the following methods of manufacture and grade as specified on the purchase order: 1.2.1 Type I, Drive PipeSeamless or electric-resistance-welded, Grades A and B. 1.2.2 Type II, Water-Well Reamed and Drifted PipeSeamless or electric-resistance-welded, Grades A and B, or furnace-butt welded. 1.2.3 Type III, Driven Well PipeSeamless or electric-resistance-welded, Grades A and B, or furnace-butt welded. 1.2.4 Type IV, Water-Well Casing Pipe Seamless or electric-resistance-welded, Grades A and B, or furnace-butt welded. 1.3 The values stated in either inch-pound units or in SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values in each system are not exact equivalents; therefore, each system is to be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.Note 1The dimensionless designator NPS (nominal pipe size) and DN (Nominal Diameter) have been substituted in this standard for such traditional terms as \"nominal diameter,\" \"size,\" and \"nominal size.\"

ASTM A694/A694M-2013高壓部件傳輸用管法蘭,配件,閥門及零件用碳素鋼及合金鋼鍛件的標準規格

1.1x00a0;This specification covers forged or rolled steel pipe flanges, forged fittings, valves, and parts suitable for use with high-strength transmission-service pipe. Included are flanges, fittings, and similar parts ordered either to dimensions specified by the purchaser or to ASME or MSS dimensional standards referenced in Section 2. 1.2x00a0;Several grades of material, based on minimum yield strength requirements, are covered, as indicated in Table 1. 1.3x00a0;Supplementary Requirements are provided. Supplementary Requirement S8201;1 is provided for use when purchaser approval is required for repair welding. 1.4x00a0;This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable x201c;Mx201d; specification designation (SI units), the material shall be furnished to inch-pound units. 1.5x00a0;The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

ASTM A694/A694M-2014高壓傳輸設備用管法蘭, 配件, 閥門及零件用碳素鋼及合金鋼鍛件的標準規格

DIN EN ISO 10440-1-2008石油、石化和天然氣工業.旋轉型容積式壓縮機.第1部分:加工壓縮機

This part of ISO 10440 specifies requirements for dry and oil-flooded, helical-lobe rotary compressors (seeFigure 1) used for vacuum or pressure or both in petroleum, petrochemical, and gas industry services. It isintended for compressors that are in special-purpose applications.It is not applicable to general-purpose air compressors, liquid-ring compressors, or vane-type compressors.NOTE Standard air compressors are covered in ISO 10440-2.

DIN EN ISO 13709-2010石油、石化和天然氣工業用離心泵

This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services.This International Standard is applicable to overhung pumps, between-bearings pumps and vertically suspended pumps (see Table 1). Clause 9 provides requirements applicable to specific types of pump. All other clauses of this International Standard are applicable to all pump types. Illustrations are provided of the various specific pump types and the designations assigned to each specific type.