碳素鋼管和低合金鋼管檢測

碳素鋼管和低合金鋼管檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 13401-2017鋼制對焊管件 技術規范

本標準規定了鋼制對焊管件(以下簡稱管件)的訂貨內容、材料、制造、熱處理、檢驗與試驗、焊接修補、表面防護與包裝和產品質量合格證明書等技術要求。本標準適用于GB/T 12459中規定的管件。其他管件亦可參照使用。

GB/T 30063-2013結構用直縫埋弧焊接鋼管

本標準規定了結構用直縫埋弧焊接鋼管的尺寸、外形、重量、技術要求、試驗方法、檢驗規則、標志、包裝和質量證明書。本標準適用于建筑、橋梁、塔架、樁柱、支桿和其他一般結構用的外徑不小于400 mm的直縫埋弧焊接鋼管(以下簡稱“鋼管”),不適用于機械結構用鋼管。

GB/T 32294-2015鍛制承插焊和螺紋活接頭

本標準規定了鍛制承插焊和螺紋活接頭的品種與代號、產品結構、級別、接管尺寸、訂貨內容、尺寸與公差、材料、制造、熱處理、檢驗和試驗以及標志等要求。本標準適用于工業管道系統中公稱尺寸不大于DN80(NPS 3)、級別為Class 3000的承插焊和螺紋活接頭。

GB 50235-2010工業金屬管道工程施工規范

本規范適用于設計壓力不大于42MPa，設計溫度不超過材料允許使用溫度的工業金屬管道工程的施工。本規范不適用于下列工業金屬管道的施工：1 石油、天然氣、地?zé)岬瓤碧胶筒删蜓b置的管道；2 長輸管道；3 核能裝置的專用管道；4 海上設施和礦井的管道；5 采暖通風與空氣調節的管道及非圓形截面的管道。

GB 50236-2011現場設備、工業管道焊接工程施工規范

為提高工程建設施工現場設備和工業金屬管道焊接工程的施工水平，加強焊接工程施工過程的質量控制，保證工程質量和安全，制定本規范。本規范適用于碳素鋼、合金鋼、鋁及鋁合金、銅及銅合金、鈦及鈦合金（低合金鈦）、鎳及鎳合金、鋯及鋯合金材料的焊接工程的施工。本規范適用的焊接方法包括氣焊、焊條電弧焊、埋弧焊、鎢極惰性氣體保護電弧焊、熔化極氣體保護電弧焊、自保護藥芯焊絲電弧焊、氣電立焊和螺柱焊。焊接工程的施工，應按設計文件及本規范的規定執行。 當需要修改設計文件及材料代用時，必須經原設計單位同意,并出具書面文件。本規范應與現行標準《現場設備、工業管道焊接工程施工質量驗收規范》GB 50683配合使用。焊接工程的施工應符合現行的節能減排、環境保護、安全技術和勞動保護等有關規定?，F(xiàn)場設備、工業管道焊接工程的施工除應符合本規范外，尚應符合現行有關標準的規定。

GB 50937-2013選煤廠管道安裝工程施工與驗收規范

本規范適用于選煤廠工藝管道安裝工程的施工與驗收。

GB/T 51012-2014鈾濃縮工廠工藝氣體管道工程施工及驗收規范

本規范適用于設計壓力1Pa~0. 8MPa(G)、設計溫度-80℃~100℃的鈾濃縮工藝氣體管道。

HG/T 20645.5-1998化工裝置管道機械設計規定 化工裝置管道機械設計技術規定

本規定適用于蒸汽夾套板強度的校核計算。

SH/T 3538-2017石油化工機器設備安裝工程施工及驗收通用規范

本規范規定了石油化工機器設備安裝過程的機器設備開箱檢驗、基礎處理和灌漿、零部件清洗和裝配、對中找正和單機試運轉的技術要求與質量標準。本規范適用于石油化工、煤化工和天然氣化工建設工程項目機器設備安裝工程的施工及驗收。

SY/T 0608-2014大型焊接低壓儲罐的設計與建造

本標準適用于具有單一垂直回轉軸，用于儲存石油中間產品(氣體或蒸氣)、成品以及其他類似液體的大型鋼制焊接低壓地上儲罐的設計與建造。本標準適用于設計壓力(表壓)小于0.1MPa (15lb/in<上標2>)，金屬溫度不高于120℃ (250℉)的儲罐。本標準的基本規定適用于低日平均環境溫度為-45℃ (-50℉)以上的建罐地區。附錄S中的低壓不銹鋼儲罐不受環境溫度的限制。附錄R適用于溫度范圍在-51℃～4. 5℃ (-60℉～+ 40℉)的冷藏產品的低壓儲罐。附錄Q適用于溫度不低于-198℃(-325℉)的液化烴氣的低壓儲罐。本標準的規定可適用于：a)盛裝或儲存液面以上存在氣相空間的液體儲罐。b)單獨盛裝或儲存氣體或蒸氣的儲罐，但不適用于懸掛式的氣體儲罐。與按本標準建造儲罐的罐體相連接的內部和外部接管，超出以下范圍的不在本標準規定范圍內：a)螺栓連接法蘭的第一個法蘭密封面。b)罐體外側螺紋連接的第一個螺紋接頭。c)焊接連接的第一道環向接頭。

DL/T 695-2014電站鋼制對焊管件

本標準規定了碳鋼、合金鋼和奧氏體不銹鋼對焊管件的基本要求。本標準適用于火力發電廠所用鋼制對焊管件及核電站內非核級鋼制對焊管件。

ASTM A192/A192M-2002(2007)高壓設備用無縫碳鋼鍋爐管標準規范

1.1 This specification covers minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for high-pressure service. 1.2 The tubing sizes and thicknesses usually furnished to this specification are x00BD; in. to 7 in. [12.7 to 177.8 mm] outside diameter and 0.085 to 1.000 in. [2.2 to 25.4 mm], inclusive, in minimum wall thickness. Tubing having other dimensions may be furnished, provided such tubes comply with all other requirements of this specification. 1.3 Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] inside diameter or 0.015 in. [0.4 mm] thickness. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the x201C;Mx201D; designation of this specification is specified in the order.

ASTM A450/A450M-2004a碳素,鐵素體和奧氏體合金鋼管的一般要求的標準規范

1.1 This specification covers a group of requirements which, with the exceptions of 4.3 and Sections 5, 6, 17, 18, 19, 20, 21, 22, and 23, are mandatory requirements to the following ASTM tubular product specifications:Title of SpecificationASTM DesignationElectric-Resistance-Welded Carbon Steel and Carbon Manganese Steel Boiler TubesA 178/A 178M Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser TubesA 179/A 179MSeamless Carbon Steel Boiler Tubes for High-Pressure ServiceA 192/A 192M Seamless Medium-Carbon Steel Boiler and Superheater Tubes A 210/A 210M Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser TubesA 214/A 214M Seamless and Electric-Welded Low-Alloy Steel Tubes A 423/A 423MElectric-Resistance-Welded Coiled Steel Tubing for Gasand Fuel Oil Lines A 539 Seamless Cold-Drawn Carbon Steel Feedwater Heater TubesA 556/A 556MSeamless, Cold-Drawn Carbon Steel Tubing for Hydraulic System ServiceA 822 These designations refer to the latest issue of the respective specifications. 1.2 One or more of Sections 4.3, 5, 6, 17, 18, 19, 20, 20.1, 22, and 23 apply when the product specification or purchase order has a requirement for the test or analysis described by these sections. 1.3 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification only the requirement of the product specification need be satisfied. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the \"M\" designation (SI) of the product specification is specified in the order.

ASTM A450/A450M-2007碳鋼和低合金鋼管一般要求的標準規范

1.1 This specification covers a group of requirements which, with the exceptions of 5.3 and Sections6, 7, 18, 19, 20, 21, 22, 23, and 24, are mandatory requirements to the following ASTM tubular product specifications:Title of SpecificationASTM DesignationElectric-Resistance-Welded Carbon Steel and Carbon Manganese Steel Boiler TubesA 178/A 178M Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser TubesA 179/A 179MSeamless Carbon Steel Boiler Tubes for High-Pressure ServiceA 192/A 192M Seamless Medium-Carbon Steel Boiler and Superheater Tubes A 210/A 210M Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser TubesA 214/A 214M Seamless and Electric-Welded Low-Alloy Steel Tubes A 423/A 423MSeamless Cold-Drawn Carbon Steel Feedwater Heater TubesA 556/A 556MSeamless, Cold-Drawn Carbon Steel Tubing for Hydraulic System ServiceA 822/A 822M These designations refer to the latest issue of the respective specifications. 1.2 One or more of Sections , , , , , , , , , and apply when the product specification or purchase order has a requirement for the test or analysis described by these sections. 1.3 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification only the requirement of the product specification need be satisfied. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the \"M\" designation (SI) of the product specification is specified in the order.

ASTM A450/A450M-2015通用要求的碳素鋼和低合金鋼管的標準規格

1.1x00a0;This specification2 covers a group of requirements which, with the exceptions of 6.3 and Sections 7, 8, 19, 20, 21, 22, 23, 24, and 25, are mandatory requirements to the following ASTM tubular product specifications:3 Title of Specification ASTM DesignationA x00a0; Electric-Resistance-Welded Carbon Steel and Carbon Manganese Steel Boiler Tubes A178/A178M Seamless Cold-Drawn Low-Carbon Steel Heat-Exchanger and Condenser Tubes A179/A179M Seamless Carbon Steel Boiler Tubes for High-Pressure Service A192/A192M Seamless Medium-Carbon Steel Boiler and Superheater Tubes A210/A210M Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes A214/A214M Seamless and Electric-Welded Low-Alloy Steel Tubes A423/A423M Specification for Seamless and Welded Carbon Steel Heat-Exchanger Tubes with Integral Fins A498 Seamless Cold-Drawn Carbon Steel Feedwater Heater Tubes

ASTM A512-2006冷拉對縫焊碳素鋼機械管的標準規范

1.1 This specification covers cold-drawn buttweld carbon steel tubes for use as mechanical tubing. 1.2 This specification covers round, square, rectangular, and special shape mechanical tubing. 1.3 Round tube size ranges covered are outside diameters up to 3 1/2 in. (88.9 mm) and wall thickness from 0.035 to 0.500 in. (0.89 to 12.70 mm).1.4 Optional supplementary requirements are provided and, when desired, shall be so stated in the order.1.5 The values stated in inch-pound-units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ASTM A513-2007電阻焊碳素鋼與合金鋼機械鋼管的標準規范

1.1 This specification covers electric-resistance-welded carbon and alloy steel tubing for use as mechanical tubing. 1.2 This specification covers mechanical tubing made from hot- or cold-rolled steel.1.3 This specification covers round, square, rectangular, and special shape tubing.TypeSize Range(Round Tubing)Electric-Resistance-Welded Tubing from Hot-Rolled Steel outside diameter from 1/2 to 15 in. (19.0 to 381.0 mm) wall from 0.065 to 0.650 in. (1.65 to 16.50 mm) Electric-Resistance-Welded Tubing from Cold-Rolled Steel outside diameter from 3/8 to 12 in. (9.92 to 304.8 mm) wall from 0.022 to 0.134 in. (0.71 to 3.40 mm) 1.4 Optional supplementary requirements are provided and when desired, shall be so stated in the order. 1.5 The values stated in inch-pound units are to be regarded as the standard.

ASTM A513-2008電阻焊碳素鋼和合金鋼機械管的標準規范

1.1 This specification covers electric-resistance-welded carbon and alloy steel tubing for use as mechanical tubing. 1.2 This specification covers mechanical tubing made from hot- or cold-rolled steel. 1.3 This specification covers round, square, rectangular, and special shape tubing. Type Size Range (Round Tubing) Electric-Resistance-Welded Tubing from Hot-Rolled Steel outside diameter from 1/2 to 15 in. (19.0 to 381.0 mm) wall from 0.065 to 0.650 in. (1.65 to 16.50 mm) Electric-Resistance-Welded Tubing from Cold-Rolled Steel outside diameter from 3/8to 12 in. (9.92 to 304.8 mm) wall from 0.022 to 0.134 in. (0.71 to 3.40 mm) 1.4 Optional supplementary requirements are provided and when desired, shall be so stated in the order. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

ASTM A513-2008a電阻焊碳素鋼與合金鋼機械鋼管標準規范

1.1 This specification covers electric-resistance-welded carbon and alloy steel tubing for use as mechanical tubing. 1.2 This specification covers mechanical tubing made from hot- or cold-rolled steel. 1.3 This specification covers round, square, rectangular, and special shape tubing. Type Size Range (Round Tubing) Electric-Resistance-Welded Tubing from Hot-Rolled Steel outside diameter from x00BD; to 15 in. (19.0 to 381.0 mm) wall from 0.065 to 0.650 in. (1.65 to 16.50 mm) Electric-Resistance-Welded Tubing from Cold-Rolled Steel outside diameter from 3/8to 12 in. (9.92 to 304.8 mm) wall from 0.022 to 0.134 in. (0.71 to 3.40 mm) 1.4 Optional supplementary requirements are provided and when desired, shall be so stated in the order. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.