鉆井液膨脹試驗用膨潤土檢測

鉆井液膨脹試驗用膨潤土檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 16783.1-2014石油天然氣工業 鉆井液現場測試 第1部分:水基鉆井液

GB/T 16783的本部分提供了水基鉆井液下述性能的測試程序:a)鉆井液密度;b)黏度和切力;c)濾失量;d)水、油和固相含量;e)含砂量;f)亞甲基藍容量;g)pH值;h)堿度和石灰含量;i)氯離子含量;j)以鈣離子計的總硬度。附錄A~附錄J提供了附加的試驗方法,可用于:--鈣離子、鎂離子、硫酸鈣、硫離子、碳酸鹽、鉀離子的化學分析;--靜切力測定;--電阻率測定;--從鉆井液中除氣;--鉆桿腐蝕監測;--取樣、檢驗和拒收;--井場取樣;--玻璃量具、溫度計、黏度計、蒸餾器杯和鉆井液密度計的檢驗和校正;--用兩種測試儀器進行高溫高壓滲透性封堵測定。附錄K提供了水基鉆井液報表格式。

GB/T 29170-2012石油天然氣工業 鉆井液 實驗室測試

本標準規定了鉆井液材料和鉆井液的物理、化學、流變等性能的實驗室測試方法。本標準適用于水基鉆井液、油基鉆井液以及其他基液或人工配制流體。本標準不適用于作為控制鉆井液性能的詳細手冊。由于攪拌條件和測試溫度對鉆井液性能影響顯著,本標準給出了推薦的攪拌條件和測試溫度。

GB/T 29172-2012巖心分析方法

本標準規定了巖心的鉆取、處理、保存及巖心分析的準備、測試方法、技術要求及編寫報告的格式、本標準適用于在油氣藏勘探、開發過程中,對鉆井取心及井壁取心巖樣的測試分析,其他巖心的分析亦應參照執行、

SY/T 5490-2016鉆井液試驗用土

本標準規定了鉆井液試驗配漿用膨潤土、鉆井液膨脹試驗用膨潤土、鉆井液用評價土的技術要求、試驗方法及標志、包裝、貯存和運輸、安全環保要求等。本標準適用于鉆井液試驗配漿用膨潤土、鉆井液膨脹試驗用膨潤土、鉆井液試驗用評價土。

SY/T 5794-2010鉆井液用瀝青類評價方法

本標準規定了鉆井液用瀝青類產品揮發份、pH值、瀝青總量、水溶物含量、油溶物含量、電動電位、軟化點等的測定方法。本標準適用于鉆井液用瀝青類產品揮發份、pH值、瀝青總量、水溶物含量、油溶物含量、電動電位、軟化點等的測定。

SY/T 5971-2016油氣田壓裂酸化及注水用粘土穩定劑性能評價方法

本標準規定了油氣田壓裂酸化及注水用黏土穩定劑的性能評價方法。本標準適用于油氣田壓裂酸化及注水用黏土穩定劑的性能測定。

TB 10014-2012鐵路工程地質鉆探規程

本規程適用于鐵路工程地質、水文地質鉆探及物探測井、孔內測試鉆孔的鉆探工作。

EN ISO 10426-1-2009石油和天然氣工業.油井固井用水泥和材料.第1部分:規范

This part of ISO 10426 specifies requirements and gives recommendations for six classes of well cements, including their chemical and physical requirements and procedures for physical testing.

DIN EN ISO 10414-1-2009石油和天然氣工業 鉆井液的現場試驗 第1部分:水基液

This part of ISO 10414 provides standard procedures for determining the following characteristics ofwater-based drilling fluids:a) drilling fluid density (mud weight);b) viscosity and gel strength;c) filtration;d) water, oil and solids contents;e) sand content;f) methylene blue capacity;g) pH;h) alkalinity and lime content;i) chloride content;j) total hardness as calcium.Annexes A through K provide additional test methods which may be used for-- chemical analysis for calcium, magnesium, calcium sulfate, sulfide, carbonate and potassium;-- determination of shear strength;-- determination of resistivity;-- removal of air;-- drill-pipe corrosion monitoring;-- sampling, inspection and rejection;-- rig-site sampling;-- calibration and verification of glassware, thermometers, viscometers, retort-kit cup and drilling-fluid balances;-- permeability-plugging testing at high temperature and high pressure for two types of equipment;-- example of a report form for water-based drilling fluid.

BS EN ISO 10426-1-2009石油和天然氣工業.固井用混凝土和材料.規范

This part of ISO 10426 specifies requirements and gives recommendations for six classes of well cements,including their chemical and physical requirements and procedures for physical testing.This part of ISO 10426 is applicable to well cement classes A, B, C and D, which are the products obtained bygrinding Portland cement clinker and, if needed, calcium sulfate as an interground additive. Processingadditives can be used in the manufacture of cement of these classes. Suitable set-modifying agents can beinterground or blended during manufacture of class D cement.This part of ISO 10426 is also applicable to well cement classes G and H, which are the products obtained bygrinding clinker with no additives other than one or more forms of calcium sulfate, water or chemical additivesas required for chromium (VI) reduction.