歡迎訪問中科光析科學技術研究所官網!

免費咨詢熱線
400-635-0567|
農業灌溉設備 灌溉閥 第4部分:進排氣閥檢測項目報價???解決方案???檢測周期???樣品要求? |
點 擊 解 答??![]() |
本文件規定了進排氣閥的設計要求、性能要求、一致性評定、標志和包裝。該進排氣閥適用于水溫不超過60 ℃,并且水中可能含有某些農業常用類型和濃度的肥料或化學物質的灌溉系統。本文件適用于公稱尺寸不小于DN 15的液力驅動式灌溉用進排氣閥,該類閥或直接通過浮子給啟閉件施加力實現運行或由機械式控桿通過浮子給啟閉件施加力實現運行。該類閥也可通過可調先導閥施加力實現運行。
本標準規定了直動式壓力調節器(以下簡稱壓力調節器)的結構、技術要求和試驗方法。該壓力調節器用于含有溫度不超過50。C的水,且水中可能含有農業灌溉常用類型和濃度的肥料和/或其他化學物質的農業灌溉系統。 本標準適用于公稱尺寸不大于80 mm的壓力調節器。
本標準規定了管道輸水灌溉工程的規劃、設計、管材與連接件、附屬設備及附屬建筑物、水泵選型及動力機配套、管道施工與設備安裝、工程質量檢驗與評定、工程驗收、工程運行維護與管理、效益分析與經濟評價等技術要求。本標準適用于新建、擴建及改建管道輸水灌溉工程的建設與管理。
本標準規定了壓力灌溉系統中水頭控制器的零部件要求以及安裝方法(簡稱為灌溉水頭控制器,其標準尺寸不大于200mm)。本標準僅適用于噴灌和微灌(小型噴灌、滴灌等)系統中水頭控制器的地上零部件。也可適用于一般性的灌溉水頭控制器。在一般性的灌溉水頭控制器上可安裝其他的灌溉控制和指令元件(例如電氣、電子、水力),但不能用于額外元件。本標準不適用于系統和/或元件中的灌溉水頭控制器有防凍要求的情況,例如干筒式水栓或其他形式的水栓。本標準沒有給出組成灌溉水頭控制器的單個元件的特殊設計及操作要求的說明,在其各自相關標準給出詳細說明。對于包含噴射農藥部件系統的灌溉水頭控制器,應設有防回流的元件及噴射檢測閥和其他安全設備(根據當?shù)貥藴屎蜅l款要求),但本標準中沒有包含此類設備要求。
本標準規定了農業灌溉設備的常用術語和定義。本標準適用于節水灌溉設備(包括噴灌機、噴灌泵、噴灌管路、噴頭等設備)設計、制造和試驗。
重要提示:對任何一個噴頭,由于噴嘴結構;運行條件和調節方式多樣化,因此至少從理論上需要進行大量相關試驗。在滿足試驗準確度要求的條件下,檢測機構和制造廠可采用插值法,以減少實際試驗次數。本部分規定了農業灌溉用噴頭水量分布特性的試驗條件和試驗方法。主要包括室內、室外雨量筒放射線布置法和雨量筒方格網布置法。本部分適用于ISO 15886-1分類中的所有類型灌溉噴頭的水量分布均勻性、噴頭射程和噴射高度等特定性能的測試。本部分不適用于移動式灌溉系統或射程小于1.0 m的噴頭。本部分未涉及冰凍條件下使用的噴頭的防凍性能試驗,也未涉及水滴光譜測量和特性以及土壤密實度、霧滴漂移、蒸發損失等相關問題。使用本部分對灌溉區域做評價時,試驗用噴頭應一致,并按可重復的固定幾何圖形布局。
This part of ISO 9635 specifies construction and performance\nrequirements and test methods for air valves, intended for\noperation in irrigation systems with water at temperatures not\nexceeding 60 °C, which can contain fertilizers and other chemicals\nof the types and concentrations used in agriculture.\nIt is applicable to hydraulically operated air irrigation valves\nof DN 15 diameter or greater, designed to be directly operated,\ni.e. the force is applied to the obturator by the float, either\ndirectly or via a mechanical linkage. The valves can be operated by\na force applied through an adjustable pilot valve.
This part of ISO 9635 specifies construction and performance requirements and test methods for air valves, intended for operation in irrigation systems with water at temperatures not exceeding 60 °C, which can contain fertilizers and other chemicals of the types and concentrations used in agriculture. It is applicable to hydraulically operated air irrigation valves of DN 15 (1/2 inch) diameter or greater, designed to be directly operated, i.e. the force is applied to the obturator by the float, either directly or via a mechanical linkage. The valves can be operated by a force applied through an adjustable pilot valve.
This part of ISO 9635 specifies construction and performance requirements and test methods for air valves, intended for operation in irrigation systems with water at temperatures not exceeding 60 ?C, which can contain fertilizers and other chemicals of the types and concentrations used in agriculture.
Specifies construction and performance requirements and test methods for air valves, intended for operation in irrigation systems with water at temperatures not exceeding 60 which can contain fertilizers and other chemicals of the types and concentr
The document applies to planning, construction and operation of irrigation equipment. It allows for an optimal exploitation of the water-supply in order to ensure the harvest and its quality. It also facilitates the use of fertilizer, it protects from frost and makes special tasks possible. It contains safety requirements for the use of irrigation equipment.
前沿科學
微信公眾號
中析研究所
抖音
中析研究所
微信公眾號
中析研究所
快手
中析研究所
微視頻
中析研究所
小紅書